Contains details of a table archival operation.

Represents an attribute for describing the key schema for the table and indexes.

Represents the data for an attribute.

For the UpdateItem operation, represents the attributes to be modified, the action to perform on each, and the new value for each.

Represents the properties of the scaling policy.

Represents the auto scaling policy to be modified.

Represents the auto scaling settings for a global table or global secondary index.

Represents the auto scaling settings to be modified for a global table or global secondary index.

Represents the properties of a target tracking scaling policy.

Represents the settings of a target tracking scaling policy that will be modified.

Contains the description of the backup created for the table.

Contains the details of the backup created for the table.

Contains details for the backup.

Represents the input of a BatchGetItem operation.

Represents the output of a BatchGetItem operation.

An error associated with a statement in a PartiQL batch that was run.

A PartiQL batch statement request.

A PartiQL batch statement response..

Represents the input of a BatchWriteItem operation.

Represents the output of a BatchWriteItem operation.

Contains the details for the read/write capacity mode.

Represents the amount of provisioned throughput capacity consumed on a table or an index.

Represents the selection criteria for a Query or Scan operation:

Represents a request to perform a check that an item exists or to check the condition of specific attributes of the item.

The capacity units consumed by an operation. The data returned includes the total provisioned throughput consumed, along with statistics for the table and any indexes involved in the operation. ConsumedCapacity is only returned if the request asked for it. For more information, see Provisioned Throughput in the Amazon DynamoDB Developer Guide.

Represents the continuous backups and point in time recovery settings on the table.

Represents a Contributor Insights summary entry.

Represents a new global secondary index to be added to an existing table.

Represents a replica to be added.

Represents a replica to be created.

Represents the input of a CreateTable operation.

Represents the output of a CreateTable operation.

Represents a request to perform a DeleteItem operation.

Represents a global secondary index to be deleted from an existing table.

Represents the input of a DeleteItem operation.

Represents the output of a DeleteItem operation.

Represents a replica to be removed.

Represents a replica to be deleted.

Represents a request to perform a DeleteItem operation on an item.

Represents the input of a DeleteTable operation.

Represents the output of a DeleteTable operation.

Represents the output of a DescribeLimits operation.

Represents the input of a DescribeTable operation.

Represents the output of a DescribeTable operation.

An endpoint information details.

Represents a condition to be compared with an attribute value. This condition can be used with DeleteItem, PutItem, or UpdateItem operations; if the comparison evaluates to true, the operation succeeds; if not, the operation fails. You can use ExpectedAttributeValue in one of two different ways:

Represents the properties of the exported table.

Summary information about an export task.

Represents a failure a contributor insights operation.

Specifies an item and related attribute values to retrieve in a TransactGetItem object.

Represents the input of a GetItem operation.

Represents the output of a GetItem operation.

Represents the properties of a global secondary index.

Represents the auto scaling settings of a global secondary index for a global table that will be modified.

Represents the properties of a global secondary index.

Represents the properties of a global secondary index for the table when the backup was created.

Represents one of the following:

Represents the properties of a global table.

Contains details about the global table.

Represents the settings of a global secondary index for a global table that will be modified.

Information about item collections, if any, that were affected by the operation. ItemCollectionMetrics is only returned if the request asked for it. If the table does not have any local secondary indexes, this information is not returned in the response.

Details for the requested item.

Represents a set of primary keys and, for each key, the attributes to retrieve from the table.

Represents a single element of a key schema. A key schema specifies the attributes that make up the primary key of a table, or the key attributes of an index.

Describes a Kinesis data stream destination.

Represents the input of a ListTables operation.

Represents the output of a ListTables operation.

Represents the properties of a local secondary index.

Represents the properties of a local secondary index.

Represents the properties of a local secondary index for the table when the backup was created.

Represents a PartiQL statment that uses parameters.

The description of the point in time settings applied to the table.

Represents the settings used to enable point in time recovery.

Represents attributes that are copied (projected) from the table into an index. These are in addition to the primary key attributes and index key attributes, which are automatically projected.

Represents the provisioned throughput settings for a specified table or index. The settings can be modified using the UpdateTable operation.

Represents the provisioned throughput settings for the table, consisting of read and write capacity units, along with data about increases and decreases.

Replica-specific provisioned throughput settings. If not specified, uses the source table's provisioned throughput settings.

Represents a request to perform a PutItem operation.

Represents the input of a PutItem operation.

Represents the output of a PutItem operation.

Represents a request to perform a PutItem operation on an item.

Represents the input of a Query operation.

Represents the output of a Query operation.

Represents the properties of a replica.

Represents the auto scaling settings of the replica.

Represents the auto scaling settings of a replica that will be modified.

Contains the details of the replica.

Represents the properties of a replica global secondary index.

Represents the auto scaling configuration for a replica global secondary index.

Represents the auto scaling settings of a global secondary index for a replica that will be modified.

Represents the properties of a replica global secondary index.

Represents the properties of a global secondary index.

Represents the settings of a global secondary index for a global table that will be modified.

Represents the properties of a replica.

Represents the settings for a global table in a Region that will be modified.

Represents one of the following:

Represents one of the following:

Contains details for the restore.

Represents the input of a Scan operation.

Represents the output of a Scan operation.

Contains the details of the table when the backup was created.

Contains the details of the features enabled on the table when the backup was created. For example, LSIs, GSIs, streams, TTL.

The description of the server-side encryption status on the specified table.

Represents the settings used to enable server-side encryption.

Represents the DynamoDB Streams configuration for a table in DynamoDB.

Represents the auto scaling configuration for a global table.

Represents the properties of a table.

Describes a tag. A tag is a key-value pair. You can add up to 50 tags to a single DynamoDB table.

The description of the Time to Live (TTL) status on the specified table.

Represents the settings used to enable or disable Time to Live (TTL) for the specified table.

Specifies an item to be retrieved as part of the transaction.

A list of requests that can perform update, put, delete, or check operations on multiple items in one or more tables atomically.

Represents a request to perform an UpdateItem operation.

Represents the new provisioned throughput settings to be applied to a global secondary index.

Represents the input of an UpdateItem operation.

Represents the output of an UpdateItem operation.

Represents a replica to be modified.

Represents the input of an UpdateTable operation.

Represents the output of an UpdateTable operation.

Represents the input of an UpdateTimeToLive operation.

Represents an operation to perform - either DeleteItem or PutItem. You can only request one of these operations, not both, in a single WriteRequest. If you do need to perform both of these operations, you need to provide two separate WriteRequest objects.

Determines the level of detail about provisioned throughput consumption that is returned in the response: